I think I'm done !!

I think I'm done !!

Joined: June 21st, 2012, 9:08 pm

January 17th, 2017, 12:33 am #1

Well I tryed.. This is a follow up on my post.
http://www.network54.com/Forum/113813/m ... 1%21%21%21
Sent it off to Tom Mace what a great guy ! He tryed and did everything he could but he doesn't have the machinery to repair it.. So I am done with air guns !! I will try to part it out.. Air tube is 36" long but 8-9" would have to be cut and machined.. 33" tj 7mm barrel.. Also any other parts not f'ed up !! Richards microfit stock.. Thank you greatly for all the help Tom !! Also thanks for all the support from all of you !!
Quote
Share

Joined: August 25th, 2013, 8:00 pm

January 17th, 2017, 10:25 pm #2

and kill some cans and for get the old gun.
Quote
Share

Joined: April 19th, 2001, 6:33 pm

January 18th, 2017, 12:11 am #3

Tim has good advice, grab a B3 and have some simple accurate plinking fun, forget the old gun. Last I looked the B3s were about $40 on Amazon
Quote
Share

Joined: May 20th, 2013, 2:59 am

January 18th, 2017, 6:23 pm #4

Well I tryed.. This is a follow up on my post.
http://www.network54.com/Forum/113813/m ... 1%21%21%21
Sent it off to Tom Mace what a great guy ! He tryed and did everything he could but he doesn't have the machinery to repair it.. So I am done with air guns !! I will try to part it out.. Air tube is 36" long but 8-9" would have to be cut and machined.. 33" tj 7mm barrel.. Also any other parts not f'ed up !! Richards microfit stock.. Thank you greatly for all the help Tom !! Also thanks for all the support from all of you !!
Needs the rear sight, but it's yours if you pay the shipping. In great shape too!

It's a B3-F model, I think. The .177 version with a removable rear sight.
Last edited by Duane35 on January 18th, 2017, 6:27 pm, edited 1 time in total.
Quote
Share

Joined: May 25th, 2013, 11:52 pm

January 18th, 2017, 11:16 pm #5

Well I tryed.. This is a follow up on my post.
http://www.network54.com/Forum/113813/m ... 1%21%21%21
Sent it off to Tom Mace what a great guy ! He tryed and did everything he could but he doesn't have the machinery to repair it.. So I am done with air guns !! I will try to part it out.. Air tube is 36" long but 8-9" would have to be cut and machined.. 33" tj 7mm barrel.. Also any other parts not f'ed up !! Richards microfit stock.. Thank you greatly for all the help Tom !! Also thanks for all the support from all of you !!
I was hoping to get it going for you. But Troy has got it so screw up the only way to get it going is cut off about 8in and put all the holes and slots back where they should be. He put the holes and slots in the air tube with a dremel hand grinder slots were put on angel the holes were big enough for two screws. Valve was cut off and the spring was on the outside which is ok if you don't have the return spring stopping the hammer from opening the valve. The hammer spring looked like it was a spring off from a bed frame. It is in bad repair like I said the air tube can be cut off and the holes and slots you could make it work a new breech should be ok but the thing has dremel marks all over it where it got away from him. It is a sorry mess lets hear it for mister f up.
Ray I want to thank you for the good words But I am sorry that I could not make work. Thank you Tom Mace
Quote
Share

Joined: June 21st, 2012, 9:08 pm

February 12th, 2017, 2:55 am #6

Well the pieces are listed in the classified now.. Still debating whether to get a high quality springer or give up!!
Quote
Share