CF-X tune. Jeff, Doug, Ken...

CF-X tune. Jeff, Doug, Ken...

Joined: October 21st, 2001, 3:36 am

July 29th, 2006, 7:45 pm #1

and one other person whom I carelessly neglected to note with the advice offered; offered pictures, tips and measurements for the CF-X. Well, It's coming apart now so any info would be greatly appreciated. I'm going to take photos, and measurements as well and would like to compare notes and then build a tuning database for this particular Gamo so don't send any secret recipes. I am going to freely offer my documentation and any other sent to me with credit to the sender, promise.

Reply
Share

Joined: February 14th, 2006, 4:12 pm

July 29th, 2006, 9:36 pm #2

rear O-ring on hand if you pull the loading port. Good luck!
Reply
Share

Joined: October 21st, 2001, 3:36 am

July 29th, 2006, 10:21 pm #3

Don't hold out on me now buddy, you gave some tips about cutting the guide to reduce preload. Do you take off the trigger first or releive the spring and then remove the trigger?



Last edited by bigbore on July 29th, 2006, 10:23 pm, edited 1 time in total.
Reply
Share

Joined: February 14th, 2006, 4:12 pm

July 30th, 2006, 1:22 am #4

off first.
Reply
Share

Joined: October 21st, 2001, 3:36 am

July 30th, 2006, 1:33 am #5

I'm not married anymore.

Reply
Share

Joined: October 21st, 2001, 3:36 am

July 30th, 2006, 1:35 am #6

and one other person whom I carelessly neglected to note with the advice offered; offered pictures, tips and measurements for the CF-X. Well, It's coming apart now so any info would be greatly appreciated. I'm going to take photos, and measurements as well and would like to compare notes and then build a tuning database for this particular Gamo so don't send any secret recipes. I am going to freely offer my documentation and any other sent to me with credit to the sender, promise.

got the call about an hour ago. Photos later tonight/tomorrow morning.

Last edited by bigbore on July 30th, 2006, 6:22 am, edited 1 time in total.
Reply
Share

Joined: October 21st, 2001, 3:36 am

July 30th, 2006, 5:52 am #7



Reply
Share

Joined: February 14th, 2006, 4:12 pm

July 30th, 2006, 6:09 am #8

Reply
Share

Joined: October 21st, 2001, 3:36 am

July 30th, 2006, 6:21 am #9

I like the gun, I believe I'll be fool'in with it for a while. With the Kodiaks, it's the springer I've always wanted. I just need to tighten it up. If I can get low 800's smooth and solid I'll be thrilled. I think I'm going to leave the breech plug in the first go around. Where do you get your breech seals?

P.S. Check out how I'm going to photo doc. it.


Last edited by bigbore on July 30th, 2006, 6:27 am, edited 1 time in total.
Reply
Share

Joined: February 14th, 2006, 4:12 pm

July 30th, 2006, 3:15 pm #10

http://www.smallparts.com/products/descriptions/ort.cfm. In a pinch, you can use a #40 from Home Depot. Those won't last as long as the Teflon, though. For the front, I don't know as I have not needed a replacement as yet. The tiny front O-ring should last a long time even with tunes. Gamo sells O-rings on their site and I believe the one they list for small rifles will work.
Reply
Share